AcuRite 00607 Spécifications Page 125
- Page / 224
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Southwestern Industries, Inc.
ProtoTRAK SMX K2, K3, K4 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual
121
6. Remove the yoke from the saddle. Disconnect the oil lines from the yoke. If the yoke is
to be re-used, it will be necessary to remove the brass nut key and pins. If the kit came with
a yoke, the original yoke may be discarded.
7. Clean the X and Y-axis gibs, oil grooves and slideways thoroughly. Also remove the
sliding covers and clean them. Inspect the operation of the oiling system.
Note: Step 7 is worth extra care, especially with machines that have some wear, or new machines that
may have some protective covering on the ways. System performance depends on smooth motion.
7.1.2 X-Axis Ball Screw Installation - Part 1
The ball screws are to be installed in the following order:
• First - part of the X-axis ball screw assembly.
• Second - the entire Y-axis ball screw assembly.
• Third - the rest of the X-axis ball screw assembly.
Parts required:
• Yoke kit 15844-xx
• X-Axis drive kit 20255 -xx
• X-Axis ball screw
Fi
gure 49
X-Axis Ball Screw
Note: There are wrench flats on the X and Y ballscrews for convenience.
CAUTION!
Unlike a leadscrew, never unscrew a ball screw from its nut.
This will destroy the ball screw.
8. Position the yoke in the saddle with the threaded hole on the left. Do not secure the
yoke to the saddle yet, you will need to lift the yoke to slide in the ball screw.
- ProtoTRAK 1
- K2, K3, K4 & 1
- Retrofit 1
- Fax 310.764.2668 2
- Fax 310.886.8029 2
- Table of Contents 3
- 1.0 Safety 6
- 1.3 Safety Precautions 8
- 2.0 Installation 11
- 2.2 Uncrating 13
- 2.5 Machine Specifications 15
- 2.9 Cleaning 21
- Placement of Levels 22
- 2.11 Electrical Connection 23
- Not for retrofit 24
- Figure 8 24
- Figure 9 25
- Figure 9-1 26
- Figure 11 29
- Transformer Option Schematic 29
- 2.14 Cable Interconnections 31
- Figure 14 33
- Pendant - Right Side 33
- P/N: 24000-1 33
- Figure 15 34
- Cable Connection Diagram 34
- Non-Spindle Control 34
- Figure 16 36
- 2.15 Lubrication 37
- 2.15.2 Head Lubrication 39
- • X = 1.318 40
- • Y = 1.318 40
- Figure 18 41
- Euclid Block 41
- 3.1.1 Poor Finish 42
- 3.1.2 Circles Out of Round 43
- 3.2.1 Run Away Axis 45
- 3.2.2 Slow Down Axis 46
- 3.2.3 Axis Will Not Jog 46
- 3.2.5 Vibration in Motion 47
- 3.2.6 Searching Axis 48
- 3.3.1 Display Blanks 49
- 3.3.3 Keyboard Lockup 49
- 3.3.4 Fault X or Y 49
- 3.3.8 System Shuts Off 51
- Machines Only) 52
- Direction 56
- 3.5.4 Head Noise 59
- 4.0 Diagnostics 61
- 4.1.3 Lubrication 62
- 4.1.4 Machining Set-Up 62
- 4.1.4.1 Spindle Speeds 63
- 4.1.4.2 Feedrates 63
- 4.4 Motor Diagnostics 66
- 4.5 Servo Driver 67
- 4.6 Glass Scales 68
- 4.7 TRAK Sensors 69
- 4.8 Electrical 71
- 4.8.4 Cable Connections 72
- Figure 19 73
- Electrical Box Schematic 73
- Figure 20 75
- Figure 21 76
- LEDs on Spindle 76
- Control Board 76
- 4.9 Service Codes 77
- 4.9.1 Software Codes 77
- 4.9.2 Machine Set-up Codes 78
- 4.9.3 Diagnostic Codes 81
- & Maintenance 84
- Figure 22 85
- Figure 23 86
- Figure 24 88
- Flash Disk Replacement 88
- Flash Disk Parts List 88
- Flask Disk Replacement 88
- 5.1.6 TRAK Sensor 89
- Figure 25 90
- M5 Base Mounting 90
- Figure 26 91
- TRAK Sensor Mounting 91
- Figure 27 92
- K Mill Sensor Assembly 92
- Z-Axis Glass Scale Assembly 95
- Figure 29 96
- Glass Scale Alignment 96
- 5.1.8 Power Drawbar 97
- Figure 30 98
- Power Drawbar Assembly 98
- Figure 31 100
- X-Axis Drive Assembly 100
- Figure 33 105
- Spindle Motor Wiring 105
- Figure 36 107
- Figure 37 109
- Figure 38 110
- 5.2 Maintenance 111
- Figure 39 111
- Table Gib Adjustment 111
- Figure 40 112
- Table Gib Screw 112
- Figure 42 114
- Figure 43 115
- Calibration Set-Up 115
- 5.2.3.2 Tramming the Head 117
- Side-to-Side Alignment 117
- Back to Front Adjustment 118
- 5.2.4 Limit Switch Option 119
- 6.0 Retrofit Installation 121
- 7.0 Installation Procedures 123
- X-Axis Ball Screw 125
- Figure 51 127
- Figure 55 133
- Figure 56 136
- X Motor Mounting 136
- Figure 58 141
- Z-Axis Glass Scale Assembly 141
- Figure 59 142
- X Bracket Installation 142
- Figure 60 143
- Y Bracket Installation 143
- Figure 61 144
- 148
- 7.9 System Interconnection 150
- Figure 66 151
- Figure 68 156
- & Covers Assembly 156
- Figure 68-1 158
- Ball Screw Module 158
- P/N 24250 158
- Parts List Ball Screw Module 159
- 8.4 Lagun Z Axis Cutout 160
- Figure 69 160
- 9.2 Warranty 161
- 9.3 Replacements 163
- Figure 100 164
- Figure 104 169
- Pulley Pinion Sub-Assembly 169
- P/N: 20697-4 169
- Figure 105 170
- Lower Vari-Disc Sub-Assembly 170
- P/N: 20697-5 170
- Figure 106 172
- Upper Vari-Disc Sub-Assembly 172
- P/N: 20697-6 172
- Figure 109 176
- Bottom Housing Assembly 176
- Figure 110 180
- P/N: 20698-1 180
- Parts List 192
- Head Top Assembly - 24692 192
- Figure 120 194
- Hi-Low Shift Clutch 194
- Sub-Assembly 194
- P/N: 20778-2 194
- Figure 121 196
- Hi-Low Shift 196
- P/N: 20778-3 196
- Figure 125 202
- Speed Change Handwheel 202
- P/N: 20778-7 202
- Figure 127 204
- Lower Head Assembly 204
- Figure 128 208
- Worm Gear Cradle 208
- P/N: 20779-1 208
- Figure 134 214
- K2/K3 Base Machine P/N 20785 214
- Figure 135 218
- K4 Base Machine P/N 26900 218
- Parts List - K4 Base Machine 219
- Figure 136 221
- P/N: 23470-220 or 23470-440 221
- Figure 137 222
- P/N 23470-220 or 23470-440 222
- TRAK Warranty Policy 224
Produits connexes et manuels pour Stations météorologiques AcuRite 00607
Whirlpool FWSG71283WCV UA manuales
Manuales del propietario y guías del usuario para Lavadoras Whirlpool FWSG71283WCV UA.
Ofrecemos 1 manuales en pdf Whirlpool FWSG71283WCV UA para descargar gratis por tipos de documentos: Guía de usuario
Whirlpool FWSG71283WCV UA Guía de usuario (4 paginas)
Marca: Whirlpool | Categoria: Washing machines | Tamaño: 1.73 MB |
Tabla de contenidos
Más productos y manuales para Lavadoras Whirlpool
| Modelos | Tipo de documento |
|---|---|
| AWO/C 72120 |
Instrucciones de uso
Whirlpool AWOC 72100 Instruction for Use,
15 paginas
|
| NLM11 946 SC A EX |
Guía de usuario
Whirlpool NLM11 946 SC A EX Setup and user guide [de] [es] [fr] [it] [nl] [pt] [ua] ,
4 paginas
|
| FWDD1071681SBS 60Hz |
Guía de usuario
Whirlpool FWDD1071681SBS 60Hz Setup and user guide,
8 paginas
|
| WT 1530 |
Instrucciones de uso
Whirlpool WT 1530 Instruction for Use,
21 paginas
|
| FWF71253SB GCC |
Instrucciones de uso
Whirlpool FWF71253SB GCC Instruction for Use [sk] ,
19 paginas
|
| AWO/C 62008 |
Instrucciones de uso
Whirlpool AWO/C 62008 Instruction for Use [de] [en] [es] [fr] [it] ,
2 paginas
|
| HSCX 80427 |
Guía de usuario
Whirlpool HSCX 80427 Setup and user guide [de] [en] [es] [fr] [it] [nl] [pt] ,
8 paginas
|
| FL 1259 |
Instrucciones de uso
Whirlpool FL 9060 Instruction for Use,
16 paginas
|
| FWL61083W PL |
Instrucciones de uso
Whirlpool FWL61083W PL Instruction for Use [en] [ro] [ua] ,
19 paginas
|
| HSCX 80427 |
Guía de usuario
Whirlpool HSCX 80427 Setup and user guide [el] [hr] [it] [nl] [tr] ,
8 paginas
|
| ECO8F 1292 (EU) |
Instrucciones de uso
  
Whirlpool ECO8F 1292 (EU) Instruction for Use [da] ,
72 paginas
|
| FWGBE81484WE |
Instrucciones de uso
Whirlpool FWGBE81484WE Instruction for Use,
20 paginas
|
| FWG91484WE CH |
Instrucciones de uso
Whirlpool FWG91484WE CH Instruction for Use,
19 paginas
|
| WWDE 7512 |
Guía de uso y cuidado
Whirlpool WWDE 7512 Use and care guide [pl] [sk] [ua] ,
38 paginas
|
| FWGBE81496WSE |
Instrucciones de uso
Whirlpool FWGBE81496WSE Instruction for Use,
19 paginas
|
| FWF X71253W PL |
Instrucciones de uso
Whirlpool FWF X71253W PL Instruction for Use,
19 paginas
|
| AV 40 (AG) 50/60 |
Instrucciones de uso
Whirlpool AV 40 (AG) 50/60 Instruction for Use [en] ,
24 paginas
|
| FRESH CARE 7212 |
Instrucciones de uso
Whirlpool FRESH CARE 7212 Instruction for Use [bg] [it] [ro] [ru] [ua] ,
19 paginas
|
| ADP 6333 WH |
Instrucciones de uso
Whirlpool ADP 6333 WH Instruction for Use,
8 paginas
|
| ADG 7633 FD A++ |
Instrucciones de uso
Whirlpool ADG 7633 FD A++ Instruction for Use,
12 paginas
|
© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels